The SST26VF016B Serial Quad I/O (SQI) flash device utilizes a 4-bit multiplexed I/O serial interface to boost performance while maintaining the compact form factor of standard serial flash devices. SST26VF016B also support full command-set compatibility to traditional Serial Peripheral Interface (SPI) protocol. Operating at frequencies reaching 104 MHz, the SST26VF016B enables minimum latency execute-in-place (XIP) capability without the need for code shadowing on an SRAM. The device’s high performance and reliability make it the ideal choice for Network Appliance, DSL and Cable Modems, Wireless Lan, Computing, Digital TV, Smart Meter, Server, Set Top Box, Automotive and other Industrial applications. Further benefits are achieved with SST’s proprietary, high-performance CMOS SuperFlash® technology, which significantly improves performance and reliability, and lowers power consumption for high bandwidth, compact designs.
Serial Interface Architecture- Nibble-wide multiplexed I/O’s with SPI-like serial command structure
Mode 0 and Mode 3,
x1/x2/x4 Serial Peripheral Interface (SPI) Protocol and SQI protocol
Burst Modes- Continuous linear burst, 8/16/32/64 Byte linear burst with wrap-around
Page-Program- 256 Bytes per page in x1 or x4 mode
Flexible Erase Capability- Uniform 4 KByte sectors, Four 8 KByte top and bottom parameter overlay blocks, One 32 KByte top and bottom overlay block, Uniform 64 KByte overlay blocks
Software Write Protection- Individual Block-Locking: 64 KByte blocks, two 32 KByte blocks, and eight 8 KByte parameter blocks
Low Power Consumption: Active Read current: 15 mA (typical @ 104 MHz), Standby Current: 15 µA (typical), Deep Power-Down Current: 2.5uA (typical)
SFDP (Serial Flash Discoverable Parameters)
Packages Available: 8-contact WDFN (6mm x 5mm), 8-lead SOIC, 8-lead SOIJ
All devices are RoHS compliant
Temperature Range:
Industrial -40C to +85C; Extended -40C to +105C
Automotive Grade 2 and 3 available
Features
• Single Voltage Read and Write Operations - 2.7-3.6V or 2.3-3.6V
• Serial Interface Architecture - Nibble-wide multiplexed I/O’s with SPI-like serial command structure - Mode 0 and Mode 3 - x1/x2/x4 Serial Peripheral Interface (SPI) Protocol
• High Speed Clock Frequency - 2.7-3.6V: 104 MHz max - 2.3-3.6V: 80 MHz max
• Burst Modes - Continuous linear burst - 8/16/32/64 Byte linear burst with wrap-around
• Superior Reliability - Endurance: 100,000 Cycles (min) - Greater than 100 years Data Retention
• Low Power Consumption: - Active Read current: 15 mA (typical @ 104 MHz) - Standby Current: 15 µA (typical)
• Fast Erase Time - Sector/Block Erase: 18 ms (typ), 25 ms (max) - Chip Erase: 35 ms (typ), 50 ms (max)
• Page-Program - 256 Bytes per page in x1 or x4 mode
• End-of-Write Detection - Software polling the BUSY bit in status register
• Flexible Erase Capability - Uniform 4 KByte sectors - Four 8 KByte top and bottom parameter overlay blocks - One 32 KByte top and bottom overlay blocks - Uniform 64 KByte overlay blocks
• Write-Suspend - Suspend Program or Erase operation to access another block/sector • Software Reset (RST) mode
• Software Write Protection - Individual-Block Write Protection with permanent lock-down capability - 64 KByte blocks, two 32 KByte blocks, and eight 8 KByte parameter blocks - Read Protection on top and bottom 8 KByte parameter blocks
SST26VF016B 封装图
SST26VF016B 封装图
SST26VF016B 封装图
SST26VF016B 封装图
SST26VF016B 封装图
SST26VF016B 封装图
SST26VF016B 引脚图
型号 | 制造商 | 描述 | 购买 |
---|---|---|---|
SST26VF016BT-104V/SN | Molex Connector Corporation | 立即购买 | |
SST26VF016BT-104V/SM | Vishay BC Components | 立即购买 | |
SST26VF016BT-104V/MF | Molex Connector Corporation | 立即购买 | |
SST26VF016B-104V/SN | Vishay BC Components | 立即购买 | |
SST26VF016B-104V/SM | Vishay BC Components | 立即购买 | |
SST26VF016B-104V/MF | Vishay BC Components | 立即购买 |
SaberRD软件自带的SPICE-to-SabreTranslator (SST) 实用程序允许您将SPICE(HSPICE、PSPICE)网表或库转换为MAST网表或模板,使用SST可以自动生成符号。
MSP-400-016-B-4-X压力传感器适用于测量液压和气压,甚至可用于测量污水、蒸汽和轻度腐蚀液等特殊介质。浸湿材料采用 17-4 PH 或 316L 不锈钢;传感器无与压力介质接触的 O 型
MSP-300-016-B-5-N-X压力传感器用于测量液体或气体压力,甚至包括污水、蒸汽、轻度腐蚀性液体等特殊介质。MSP300压力传感器的压力腔由 17-4 PH 或 316L 不锈钢实心
MSP-400-016-B-4-X压力传感器适用于测量液压和气压,甚至可用于测量污水、蒸汽和轻度腐蚀液等特殊介质。浸湿材料采用 17-4 PH 或 316L 不锈钢;传感器无与压力介质接触的 O 型
MSP-300-016-B-5-N-X压力传感器用于测量液体或气体压力,甚至包括污水、蒸汽、轻度腐蚀性液体等特殊介质。MSP300压力传感器的压力腔由 17-4 PH 或 316L 不锈钢实心
MSP-300-016-B-5-B-2压力传感器在液压系统中主要是用来完成力的闭环控制。当控制阀芯忽然挪动时,在极短的时间内会构成几倍于系统工作压力的尖峰压力。在典型的行走机械和工业液压中,假如设计时没有思索到这样的工况,MSP-300-016-B-5-B-2压力传感器很快就会被毁坏。
MSP-300-016-B-4-N-X压力传感器安装在测速端盖上,感应导磁体上的凸齿或凹槽,并给出相应的高低电平,用于 检测车轴的速度、线速度,也可以通过计算处理得到被测体的加速度,该传感器具有良好
MSP-300-016-B-5-N-2 压力是旋转电力系统中最常涉及的参数,用于检测气压、水压。传感器安装在弹性轴的两端,有两组齿数、形状和安装角度相同的齿轮,齿轮外侧安装有接近(磁性或光学)传感器
STTS2004 | STPS1150 | STPS20L60C | SSM2305 |
SSM2380 | SSM3582 | STPS20S100C | STPSC12H065 |
STPS1L60 | STK672-432BN-E | STPS3L60S | STPSC8H065C |
STTH1302 | STPS20L60C-Y | SST26WF016B | SN54HC04-DIE |
STTH30L06-Y | STPS40M100C | STPS30120DJF | SST25PF020B |